-
EXTERNAL RETAINER RINGS (TRU-ARC TYPE) -
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
NOTE: Sizes (Dash No.) corresponds to standard O-ring numbersSEAL INFORMATION MATERIAL 55D HYTREL TEMPERATURE RANGE -65° TO +275°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.) -
Molded of 90A Durometer Buna-N Rubber, these 'Parback®' Style Dished Cross Section back-up rings provide excellent extrusion resistance. Stretched for installation, they return quickly to their original size for easy installation.
NOTE: Sizes (Dash No.) corresponds to standard O-ring numbers.SEAL INFORMATION MATERIAL 90A BUNA-N RUBBER TEMPERATURE RANGE -40° TO +240°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.) -
Letter suffix:
T = Solid, ST = Split, TS = Spiral Cut, TW = .085 WideSEAL INFORMATION MATERIAL PTFE TEMPERATURE RANGE -325 ° TO +500°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.)(Config)
CROSS SECTIONS 000 Series 1/16" C/S 100 Series 3/32" C/S 200 Series 1/8" C/S 300 Series 3/16" C/S 400 Series 1/4" C/S -
Molded of 95A Durometer Urethane these back-up rings provide excellent extrusion resistance. Stretched for installation, they return quickly to their original size for easy installation.
NOTE: Sizes (Dash No.) corresponds to standard o-ring numbers.SEAL INFORMATION MATERIAL 95A DUROMETER URETHANE TEMPERATURE RANGE -65 ° TO +220°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.) -
Split NylonSEAL INFORMATION MATERIAL NYLON TEMPERATURE RANGE -40 ° TO +250°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.) -
Used primarily as an anti-extusion device for u-seals, these back-up rings combine high performance with very low friction. 'ST' suffix designates a split ring.
SEAL INFORMATION MATERIAL PTFE TEMPERATURE RANGE -100° TO +500°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (prefix) - (Dash No.) (config.) -
Note: "SC" suffix designates a Scarf Cut wear ring.
SEAL INFORMATION TEMPERATURE RANGE -40° to +275° F TENSILE STRENGTH 27,000 PSI COMPRESSIVE STRENGTH 26,000 PSI PART NUMBER (PREFIX) - (OD) - (HT) CROSS-SECTIONS 606 Prefix 1/16" C/S 608 Prefix 5/64" C/S 609 Prefix 3/32" C/S 610 Prefix .1" C/S 612 Prefix 1/8" C/S 616 Prefix 3/16" C/S 625 Prefix 1/4" C/S -
NOTE: The 6000 piston cups are center punched if there is no hole size indicated.
SEAL INFORMATION MATERIAL BUNA-N RUBBER TEMPERATURE RANGE -40° to +220° F PRESSURE RANGE 0 to 150 PSI SPEED 3 FT/SEC PART NUMBER (Piston Cup Type)(Bore) - (Hole Size) -
To obtain best results from any style of piston cup, it is recommended that the piston properly support the heel of the cup. Recommended diametral clearance between the piston and cylinder wall are as follows:
1" to 2-1/4" .005"
2-1/2" to 4-3/4" .008"
5" to 10" .010"
The height of the machined shoulder most frequently used to control squeeze on the heel of the cup is as follows:
Cups 1/8" thick .116/.119"
Cups 5/32" thick .146/.149"
Cups 3/16" thick .178/.181"
The follower plate should be approximately .110" smaller than the ID of the cup. To reduce any tendency of the cup to extrude under pressure a phonograph finish may be machined on the surface of the follower plate.
NOTE: The 8000 piston cups are center punched.
SEAL INFORMATION MATERIAL 90A URETHANE TEMPERATURE RANGE -65° to +220° F PRESSURE RANGE 0 to 1,200 PSI SPEED 3 FT/SEC PART NUMBER (Piston Cup Type)(Bore) - (Hole Size) -
835 Homogeneous Rubber Vee RingsSEAL INFORMATION MATERIAL 70 DURO BUNA-N TEMPERATURE RANGE -40° to +220° F PRESSURE RANGE 0 to 1,250 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (Size) -
If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.
SEAL INFORMATION MATERIAL FABRIC REINFORCED RUBBER
AND BUNA-NTEMPERATURE RANGE -40° TO +250° F PRESSURE RANGE SEE CHART BELOW SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (ID) - (OD) A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.
PRESSURE RATING OF MULTIPLE RINGS PRESSURE P.S.I. NUMBER OF RINGS 250 - 500 3 500 - 2,000 4 2,000 - 5,000 5 5,000 - 8,000 6 -
If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.
SEAL INFORMATION MATERIAL FABRIC REINFORCED RUBBER
AND BUNA-NTEMPERATURE RANGE -40° TO +250° F PRESSURE RANGE SEE CHART BELOW SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (ID) - (OD) A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.
PRESSURE RATING OF MULTIPLE RINGS PRESSURE P.S.I. NUMBER OF RINGS 250 - 500 3 500 - 2,000 4 2,000 - 5,000 5 5,000 - 8,000 6 -
If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.
SEAL INFORMATION MATERIAL FABRIC REINFORCED RUBBER
AND BUNA-NTEMPERATURE RANGE -40° TO +250° F PRESSURE RANGE SEE CHART BELOW SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (ID) - (OD) A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.
PRESSURE RATING OF MULTIPLE RINGS PRESSURE P.S.I. NUMBER OF RINGS 250 - 500 3 500 - 2,000 4 2,000 - 5,000 5 5,000 - 8,000 6 -
If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.
SEAL INFORMATION MATERIAL FABRIC REINFORCED RUBBER
AND BUNA-NTEMPERATURE RANGE -40° TO +250° F PRESSURE RANGE SEE CHART BELOW SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (ID) - (OD) A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.
PRESSURE RATING OF MULTIPLE RINGS PRESSURE P.S.I. NUMBER OF RINGS 250 - 500 3 500 - 2,000 4 2,000 - 5,000 5 5,000 - 8,000 6
