• EXTERNAL RETAINER RINGS (TRU-ARC TYPE)
  • 568 BOSS O-RINGS

    $0.71$18.39
    568, 90 Duro Buna-N O-Ring Boss Gaskets For Straight Thread Fittings
    SEAL INFORMATION
    MATERIAL 90 DUROMETER, BUNA-N RUBBER
    TEMPERATURE RANGE -40° TO +240°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (prefix) (Dash No.) (90 Duro Fluorocarbon)
    568, 90 Duro FLUOROCARBON O-Ring Boss Gaskets For Straight Thread Fittings
    SEAL INFORMATION
    MATERIAL FLUOROCARBON
    TEMPERATURE RANGE -20° TO +400° F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (Prefix) - (Dash No.) - (90 Duro Fluorocarbon)
  • 568 O-RINGS

    $0.07$189.26
    SCS offers material advantages of with our family of urethanes in standard o-ring sizes. The high extrusion resistance and related compounds eliminates the need for a back-up in many hydraulic applications, thereby simplifying installation and reducing groove width. Our unmatched temperature rating makes it suitable in applications where other urethanes fail. In addition, Our O-rings provides superior water resistance and compression set resistance in water-based fluids. Premium urethane o-rings are much less prone to spiral failure and installation damage compared with rubber o-rings. Dimensions and tolerances of our o-rings match up with AS568B specifications for diameter and cross-section and are used in the same grooves. 90D = 90 Durometer B = Bulk (Min Quantities) V = Viton (Fluorocarbon) T = 55-58 Shore D PTFE U = 90A Urethane V-BLACK = Black Viton (Fluorocarbon) EP = Ethylene Propylene S = Silicone
    SEAL INFORMATION
    MATERIAL BUNA-N RUBBER
    TEMPERATURE RANGE -40° TO +240°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (prefix) - (Dash No.)
  • SCS offers material advantages of with our family of urethanes in standard o-ring sizes. The high extrusion resistance and related compounds eliminates the need for a back-up in many hydraulic applications, thereby simplifying installation and reducing groove width. Our unmatched temperature rating makes it suitable in applications where other urethanes fail. In addition, Our O-rings provides superior water resistance and compression set resistance in water-based fluids. Premium urethane o-rings are much less prone to spiral failure and installation damage compared with rubber o-rings. Dimensions and tolerances of our o-rings match up with AS568B specifications for diameter and cross-section and are used in the same grooves. 90D = 90 Durometer B = Bulk (Min Quantities) V = Viton (Fluorocarbon) T = 55-58 Shore D PTFE U = 90A Urethane V-BLACK = Black Viton (Fluorocarbon) EP = Ethylene Propylene S = Silicone
    SEAL INFORMATION
    MATERIAL BUNA-N RUBBER
    TEMPERATURE RANGE -40° TO +240°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (prefix) - (Dash No.)
  • SEAL INFORMATION
    MATERIAL BUNA-N RUBBER
    TEMPERATURE RANGE -40° TO +240°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (prefix) (Cord) - (Nom. Size) (Fluorocarbon)

    568, 75 DURO FLUOROCARBON O-RING CORD

    Cord is Black fluorocarbon. See O-Ring Kit section for Splicing Information.
    SEAL INFORMATION
    MATERIAL BLACK FLUOROCARBON
    TEMPERATURE RANGE -20° TO +400°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (Prefix) (Cord) - (Nom. Size.) (Fluorocarbon)
  • 573 BACK-UP RINGS

    $0.78$14.74

    Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
    NOTE: Sizes (Dash No.) corresponds to standard O-ring numbers

    SEAL INFORMATION
    MATERIAL 55D HYTREL
    TEMPERATURE RANGE -65° TO +275°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (Prefix) - (Dash No.)
  • 574 BACK-UP RINGS

    $0.35$15.27

    Molded of 90A Durometer Buna-N Rubber, these 'Parback®' Style Dished Cross Section back-up rings provide excellent extrusion resistance. Stretched for installation, they return quickly to their original size for easy installation.
    NOTE: Sizes (Dash No.) corresponds to standard O-ring numbers.

    SEAL INFORMATION
    MATERIAL 90A BUNA-N RUBBER
    TEMPERATURE RANGE -40° TO +240°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (Prefix) - (Dash No.)
  • 575 PTFE BACK-UP RINGS

    $1.27$123.94

    Letter suffix:
    T = Solid, ST = Split, TS = Spiral Cut, TW = .085 Wide

    SEAL INFORMATION
    MATERIAL PTFE
    TEMPERATURE RANGE -325 ° TO +500°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (Prefix) - (Dash No.)(Config)

    CROSS SECTIONS
    000 Series 1/16" C/S
    100 Series 3/32" C/S
    200 Series 1/8" C/S
    300 Series 3/16" C/S
    400 Series 1/4" C/S
  • Molded of 95A Durometer Urethane these back-up rings provide excellent extrusion resistance. Stretched for installation, they return quickly to their original size for easy installation.
    NOTE: Sizes (Dash No.) corresponds to standard o-ring numbers.

    SEAL INFORMATION
    MATERIAL 95A DUROMETER URETHANE
    TEMPERATURE RANGE -65 ° TO +220°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (Prefix) - (Dash No.)
  • 576 BACK-UP RINGS

    $3.58$57.89
    Split Nylon
    SEAL INFORMATION
    MATERIAL NYLON
    TEMPERATURE RANGE -40 ° TO +250°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (Prefix) - (Dash No.)
  • 580 SQUARE O-RINGS

    $0.25$40.87
    SEAL INFORMATION
    MATERIAL BUNA-N RUBBER
    TEMPERATURE RANGE -40° TO +240° F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (Dash No.)
  • 595 BACK-UP RINGS

    $7.57$80.10

    Used primarily as an anti-extusion device for u-seals, these back-up rings combine high performance with very low friction. 'ST' suffix designates a split ring.

    SEAL INFORMATION
    MATERIAL PTFE
    TEMPERATURE RANGE -100° TO +500°F
    PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE
    PART NUMBER (prefix) - (Dash No.) (config.)
  • 600 NYLON WEAR RINGS

    $2.98$890.58

    Note: "SC" suffix designates a Scarf Cut wear ring.

    SEAL INFORMATION
    TEMPERATURE RANGE -40° to +275° F
    TENSILE STRENGTH 27,000 PSI
    COMPRESSIVE STRENGTH 26,000 PSI
    PART NUMBER (PREFIX) - (OD) - (HT)
    CROSS-SECTIONS
    606 Prefix 1/16" C/S
    608 Prefix 5/64" C/S
    609 Prefix 3/32" C/S
    610 Prefix .1" C/S
    612 Prefix 1/8" C/S
    616 Prefix 3/16" C/S
    625 Prefix 1/4" C/S
  • 6000 PISTON CUPS

    $5.03$82.02

    NOTE: The 6000 piston cups are center punched if there is no hole size indicated.

    SEAL INFORMATION
    MATERIAL BUNA-N RUBBER
    TEMPERATURE RANGE -40° to +220° F
    PRESSURE RANGE 0 to 150 PSI
    SPEED 3 FT/SEC
    PART NUMBER (Piston Cup Type)(Bore) - (Hole Size)
  • Flexible Guide Bearings are strips of filled PTFE. The material can be cut to any length to fit any rod or bore size without losing its concentricity. The filler material is shown below. NOTE: Glass filled material has a thickness tolerance of ±_.010 in. Bronze filled tolerance is ± .0025 in.

    SEAL INFORMATION
    MATERIAL GLASS FILLED 60% BRONZE FILLED PTFE
    TEMPERATURE RANGE -50° to +400° F
    TENSILE STRENGTH 2,100 PSI
    COMPRESSIVE STRENGTH 1,500 PSI
    SPEED 12 FT/SEC
    PART NUMBER (Prefix) - (Width)
    B = Bronze Filled PTFE
  • Our 612F style flexible guide bearings, with a 1/8" radial thickness, offered in a boxed quantity. The strip can be cut to any length using anvil type pruning shears. Product length is 32' per box.

    SEAL INFORMATION
    MATERIAL FABRICATED REINFORCED POLYESTER
    TEMPERATURE RANGE -40° to +250° F
    TENSILE STRENGTH 8,000 PSI
    COMPRESSIVE STRENGTH 24,000 PSI
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (W) x (TH)
  • Manufactured using woven fabric-reinforced polyester resin, this material produces a dimensionally accurate rectangular strip which can be cut to any length. Low coefficient of friction and high compressive strength makes it an ideal bearing material. A common radial thickness of 1/8 in. allows the stacking of various widths. Size reference is marked every 6 in. on the strip. Available by the foot or rolls of 16 feet. Cutting is made easy by using Anvil type pruning shears. Wall tolerance ± .002 in., radial wall thickness = 0.124 to 0.121 in. Standard part numbers are gray in color.

    TQ = Turquoise in color.
    SEAL INFORMATION
    TEMPERATURE RANGE -40° to +250° F
    TENSILE STRENGTH 8,000 PSI
    COMPRESSIVE STRENGTH 24,000 PSI
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (Width)
  • 614 NYLON ROD BEARINGS

    $6.65$123.00

    Style 614 rod bearings are available in nylon material. These products are used extensively in hydraulic cylinders due to their low rate of wear and non-scoring properties. Excellent for those heavy duty applications that require a sturdy bearing. Most of these bearings are solid, although some may be split.

    SEAL INFORMATION
    TEMPERATURE RANGE -40° to +275° F
    TENSILE STRENGTH 25,000 PSI
    COMPRESSIVE STRENGTH 26,000 PSI
    PART NUMBER (Prefix) - (ID) - (Width)
  • 615 PHENOLIC BEARINGS

    $12.98$71.62
    SEAL INFORMATION
    TEMPERATURE RANGE -40° to +250° F
    TENSILE STRENGTH 10,600 PSI
    COMPRESSIVE STRENGTH 34,000 PSI
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (OD) (CS) - (Width)
  • 660 BRONZE ROD BEARINGS

    $62.35$122.10
    SEAL INFORMATION
    TENSILE STRENGTH 35,000 PSI
    YIELD STRENGTH 18,000 PSI
    PART NUMBER (Prefix) - (ID) (CS) - (Width)
  • 8000 PISTON CUPS

    $8.73$53.06

    To obtain best results from any style of piston cup, it is recommended that the piston properly support the heel of the cup. Recommended diametral clearance between the piston and cylinder wall are as follows:
    1" to 2-1/4" .005"
    2-1/2" to 4-3/4" .008"
    5" to 10" .010"

    The height of the machined shoulder most frequently used to control squeeze on the heel of the cup is as follows:
    Cups 1/8" thick .116/.119"
    Cups 5/32" thick .146/.149"
    Cups 3/16" thick .178/.181"
    The follower plate should be approximately .110" smaller than the ID of the cup. To reduce any tendency of the cup to extrude under pressure a phonograph finish may be machined on the surface of the follower plate.

    NOTE: The 8000 piston cups are center punched.

    SEAL INFORMATION
    MATERIAL 90A URETHANE
    TEMPERATURE RANGE -65° to +220° F
    PRESSURE RANGE 0 to 1,200 PSI
    SPEED 3 FT/SEC
    PART NUMBER (Piston Cup Type)(Bore) - (Hole Size)
  • 835 Homogeneous Rubber Vee Rings
    SEAL INFORMATION
    MATERIAL 70 DURO BUNA-N
    TEMPERATURE RANGE -40° to +220° F
    PRESSURE RANGE 0 to 1,250 PSI
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (Size)
  • 850 WV PACKING

    $9.98$47.73

    If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.

    SEAL INFORMATION
    MATERIAL FABRIC REINFORCED RUBBER
    AND BUNA-N
    TEMPERATURE RANGE -40° TO +250° F
    PRESSURE RANGE SEE CHART BELOW
    SPEED 1.5 FT/SEC
    PART NUMBER (Prefix) - (ID) - (OD)

    A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.

    PRESSURE RATING OF MULTIPLE RINGS
    PRESSURE P.S.I. NUMBER OF RINGS
    250 - 500 3
    500 - 2,000 4
    2,000 - 5,000 5
    5,000 - 8,000 6
  • 851 WV PACKING

    $6.65$44.98

    If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.

    SEAL INFORMATION
    MATERIAL FABRIC REINFORCED RUBBER
    AND BUNA-N
    TEMPERATURE RANGE -40° TO +250° F
    PRESSURE RANGE SEE CHART BELOW
    SPEED 1.5 FT/SEC
    PART NUMBER (Prefix) - (ID) - (OD)

    A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.

    PRESSURE RATING OF MULTIPLE RINGS
    PRESSURE P.S.I. NUMBER OF RINGS
    250 - 500 3
    500 - 2,000 4
    2,000 - 5,000 5
    5,000 - 8,000 6
  • 852 WV PACKING

    $6.65$43.07

    If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.

    SEAL INFORMATION
    MATERIAL FABRIC REINFORCED RUBBER
    AND BUNA-N
    TEMPERATURE RANGE -40° TO +250° F
    PRESSURE RANGE SEE CHART BELOW
    SPEED 1.5 FT/SEC
    PART NUMBER (Prefix) - (ID) - (OD)

    A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.

    PRESSURE RATING OF MULTIPLE RINGS
    PRESSURE P.S.I. NUMBER OF RINGS
    250 - 500 3
    500 - 2,000 4
    2,000 - 5,000 5
    5,000 - 8,000 6
  • 853 WV PACKING

    $7.53$25.55

    If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.

    SEAL INFORMATION
    MATERIAL FABRIC REINFORCED RUBBER
    AND BUNA-N
    TEMPERATURE RANGE -40° TO +250° F
    PRESSURE RANGE SEE CHART BELOW
    SPEED 1.5 FT/SEC
    PART NUMBER (Prefix) - (ID) - (OD)

    A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.

    PRESSURE RATING OF MULTIPLE RINGS
    PRESSURE P.S.I. NUMBER OF RINGS
    250 - 500 3
    500 - 2,000 4
    2,000 - 5,000 5
    5,000 - 8,000 6
  • 855 WV PACKING

    $8.86$23.55
    C = CARBOXILATED NITRILE
    SEAL INFORMATION
    MATERIAL FABRIC REINFORCED RUBBER
    AND BUNA-N
    TEMPERATURE RANGE -40° TO +250° F
    PRESSURE RANGE SEE CHART BELOW
    SPEED 1.5 FT/SEC
    PART NUMBER (Prefix) - (ID) - (OD)

    If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.

    PRESSURE RATING OF MULTIPLE RINGS
    PRESSURE P.S.I. NUMBER OF RINGS
    250 - 500 3
    500 - 2,000 4
    2,000 - 5,000 5
    5,000 - 8,000 6

    A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.

  • 870 U-SEALS

    $1.16$110.04
    Style 870 u-seals are precision molded from Buna-N synthetic rubber. Style 870 u-seal numbers conform in size to Army-Navy specification AN6226.
    • MATERIAL 70A BUNA-N RUBBER
    • TEMPERATURE RANGE -40° to +240° F
    • PRESSURE RANGE 0 to 500 PSI
    • SPEED 3 FT/SEC
    • PART NUMBER (Prefix)(CS) - (A-N Dash Number)
  • 9000 PISTON CUPS

    $7.05$170.73

    Piston cups are constructed of rubberized fabric. Cups with no hole are center punched.
    NOTE: If Product number ends in 'ED' the piston cups are specially sized for use in EDBRO Cylinders.

    SEAL INFORMATION
    MATERIAL COTTON FABRIC & RUBBER
    TEMPERATURE RANGE -35° to +220° F
    PRESSURE RANGE 0 to 2,500 PSI
    SPEED 1.5 FT/SEC
    PART NUMBER (Piston Cup Type)(Bore) - (Hole Size)
  • PTFE Vee Rings
    SEAL INFORMATION
    MATERIAL PTFE
    TEMPERATURE RANGE -100° to +400° F
    PRESSURE RANGE 0 to 5,000 PSI
    SPEED 12 FT/SEC
    PART NUMBER (Prefix) - (Size)
  • AN WIPER RINGS

    $1.29$31.84

    Suffix 'SH' designates slotted heel design, 'V' designates fluorocarbon material, and 'B' designates carboxilated nitrile material.

    SEAL INFORMATION
    MATERIAL 90A URETHANE
    TEMPERATURE RANGE -40° to +200° F
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (Size)
  • BT WIPER RINGS

    $3.11$12.64
    SEAL INFORMATION
    MATERIAL 90A URETHANE
    TEMPERATURE RANGE -40° to +200° F
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) (Size)
  • BUNA-N WIPER CORD

    $1.97$2.85
    Buna-N Wiper Cord
  • c

    $7.37$58.14

    NOTE: Piston diameter 'I' dimensions are given for pistons without wear rings.

    SEAL INFORMATION
    MATERIAL 15% GLASS FILLED PTFE SEAL RUBBER ENERGIZER
    TEMPERATURE RANGE -40° to +220° F
    PRESSURE RANGE 0 to 5,000 PSI
    SPEED 12 FT/SEC
    PART NUMBER (Piston Seal)(Type of Seal) - (Size)
  • CAS CASCADE WIPER RINGS

    $19.39$52.87
    SEAL INFORMATION
    MATERIAL URETHANE
    TEMPERATURE RANGE -65 ° TO +220°F
    SPEED 3 FT/SEC
    PART NUMBER (prefix)(size)
  • CASCADE VEE PACKING SETS

    $19.31$90.80
    Employed mainly in cylinders made by Cascade Corp., these vee sets are often over-sized or are different from standard vee sets. They are often used with Follower bearings.
    SEAL INFORMATION
    MATERIAL FABRIC REINFORCED RUBBER AND URETHANE RINGS/NYLON ADAPTORS
    TEMPERATURE RANGE -35° to +220° F
    PRESSURE RANGE 0 to 10,000 PSI
    SPEED 1.5 FT/SEC
    PART NUMBER (Prefix) (ID) (CS) X (Height)
  • CAT CAPPED PISTON T-SEALS

    $121.18$312.24

    INSTALLATION OF PTFE PISTON SEALS
    Installing PTFE piston seals is not always an easy task. The use of installation tools (Designated by a 'CTC-' product code prefix) is recommended but often not convenient when working with a wide variety of sizes and applications. Finger installations are practical with rings of smaller cross-sections. Using fingers or a rounded plastic stick, knead the ring over the piston into the groove. With rings of larger cross-sections it may be necessary to heat the ring. Warming the ring in water or oil at 130° F or 140° F for about 5 minutes will soften the material for easier installation. Always avoid inconsistent stretching or overstretching of the PTFE seal.

    To prevent the PTFE ring from snapping into the wrong groove, cover wear ring grooves with plastic tape.

    After seal installation, assembly of the cylinder may be difficult if the piston seal is loose on the piston or the cylinder has an inadequate leading edge chamfer. In such cases, compress the piston seal with belting or a suitable hose clamp. If the piston seal must pass threads or any other sharp edges during the cylinder assembly, cover the edges with plastic tape or wrap. Note: Caterpillar part number are used as a refernce only. We do not imply that these part are original equipment parts.

    SEAL INFORMATION
    MATERIAL BUNA-N RUBBER SEAL
    - HARD PLASTIC BACK-UPS
    TEMPERATURE RANGE -40° to +220° F
    PRESSURE RANGE 0 to 6,000 PSI
  • CPS CAPPED PISTON T-SEALS

    $46.70$246.42

    A heavy duty double-acting assembly, the capped piston T-seal exhibits excellent sealability, extrusion resistance and wearability. T-seals with 'BR' suffix utilize a Bronze Filled PTFE cap instead of the standard Glass Filled PTFE cap.

    INSTALLATION OF PTFE PISTON SEALS
    Installing PTFE piston seals is not always an easy task. The use of installation tools (Designated by a 'CTC-' product code prefix) is recommended but often not convenient when working with a wide variety of sizes and applications. Finger installations are practical with rings of smaller cross-sections. Using fingers or a rounded plastic stick, knead the ring over the piston into the groove. With rings of larger cross-sections it may be necessary to heat the ring. Warming the ring in water or oil at 130° F or 140° F for about 5 minutes will soften the material for easier installation. Always avoid inconsistent stretching or overstretching of the PTFE seal.

    To prevent the PTFE ring from snapping into the wrong groove, cover wear ring grooves with plastic tape.

    After seal installation, assembly of the cylinder may be difficult if the piston seal is loose on the piston or the cylinder has an inadequate leading edge chamfer. In such cases, compress the piston seal with belting or a suitable hose clamp. If the piston seal must pass threads or any other sharp edges during the cylinder assembly, cover the edges with plastic tape or wrap.

    SEAL INFORMATION
    MATERIAL PTFE CAP
    NYLON BACK-UP
    RUBBER ENERGIZER
    TEMPERATURE RANGE -40° to +220° F
    PRESSURE RANGE 0 to 6,000 PSI
    SPEED 4.5 FT/SPEED>
    PART NUMBER (Prefix) - (Bore Size)
  • CSW WIPER RINGS

    $4.21$13.62
    Snap-In Wiper
    SEAL INFORMATION
    MATERIAL NYLON
    TEMPERATURE RANGE -40° to +212° F
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (Size)
  • CSWM WIPER RINGS

    $4.60$36.23

    This wiper is a heavy duty scraper molded from a hard nylon material.

    SEAL INFORMATION
    MATERIAL NYLON
    TEMPERATURE RANGE -40° to +212° F
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (ID) x (OD) X (H)
  • Caterpillar - 1 Piece Rod Buffer Seal
    SEAL INFORMATION
    MATERIAL 92A URETHANE
    TEMPERATURE RANGE -40° TO +200° F
    PRESSURE RANGE 0 to 5,000 PSI
    SPEED 3 FT/SEC 12FT/SEC
  • BRONZE FILLED PTFE ROD BUFFER SEAL
    SEAL INFORMATION
    MATERIAL BRONZE FILLED PTFE SEAL
    RUBBER ENERGIZER
    TEMPERATURE RANGE -40° TO +220° F
    PRESSURE RANGE 0 to 5,000 PSI
    SPEED 3 FT/SEC 12FT/SEC
  • Out of stock
    These lip-type buffer seals are designed for replacement in Caterpillar® cylinders. The hinged-lip design reduces friction, heat, and wear under low-pressure conditions and acts as a check valve allowing back-pressure relief. Seals for rod sizes 2-1/8" and under do not have a back-up ring. Caterpillar Specific Buffer Seals - DYR Style
    CATERPILLAR DYR SEAL INFORMATION
    MATERIAL URETHANE
    TEMPERATURE RANGE -22° TO +230° F
    PRESSURE RANGE 0 to 6,000 PSI
    SPEED 3 FT/SEC 12 FT/SEC
  • CTC PISTON SEAL ASSEMBLIES

    $12.08$132.62

    NOTE: Caterpillar part numbers are used as a reference only. We do not imply that these parts are original equipment parts.

  • CWN WIPER RINGS

    $2.98$6.67
    Metal Clad Wiper
    SEAL INFORMATION
    MATERIAL BUNA-N
    TEMPERATURE RANGE -22° to +212° F
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (Size)
  • DAPC PISTON CUPS

    $29.53$162.86

    One Piece Double Acting Piston Cups
    This complete piston cup with a simple, one-piece construction serves the same purpose as a multi-assembly unit and is more economical with easy maintenance, dependability and long life. The unique piston cup consists of homogeneous rubber bonded to a zinc coated steel plate. The center hole may be enlarged to accommodate larger piston rods. Recommended for pneumatic and low-pressure hydraulic applications.

    SEAL INFORMATION
    MATERIAL RUBBER LIP, ZINC COATED STEEL PLATE
    TEMPERATURE RANGE -40° to +220° F
    PRESSURE RANGE 0 to 800 PSI
    SPEED 3 FT/SEC
    PART NUMBER (Prefix) - (Bore Size)
  • DPU PISTON U-SEALS

    $8.08$223.33
    Specifically designed as piston seals, these u-seals are engineered to seal on their outside diameter. They offer extended service life and maximum reliability in piston sealing.
    • MATERIAL 92A URETHANE
    • TEMPERATURE RANGE -65° to +230° F
    • PRESSURE RANGE 0 to 6,000 PSI
    • SPEED 3 FT/SEC
    • PART NUMBER (Prefix)(CS) - (ID) - (Height)
    MAXIMUM EXTRUSION GAP PRESSURE / MAX. DIAM. GAP: | 1,000 PSI/.032 | | 3,000 PSI/.015 | | 5,000 PSI/.012 | | 6,000 PSI/.009 |
Go to Top