| SEAL INFORMATION | |
|---|---|
| MATERIAL | 70 DURO BUNA-N |
| TEMPERATURE RANGE | -40° to +220° F |
| PRESSURE RANGE | 0 to 1,250 PSI |
| SPEED | 3 FT/SEC |
| PART NUMBER | (Prefix) - (Size) |
-
835 Homogeneous Rubber Vee Rings -
To obtain best results from any style of piston cup, it is recommended that the piston properly support the heel of the cup. Recommended diametral clearance between the piston and cylinder wall are as follows:
1" to 2-1/4" .005"
2-1/2" to 4-3/4" .008"
5" to 10" .010"
The height of the machined shoulder most frequently used to control squeeze on the heel of the cup is as follows:
Cups 1/8" thick .116/.119"
Cups 5/32" thick .146/.149"
Cups 3/16" thick .178/.181"
The follower plate should be approximately .110" smaller than the ID of the cup. To reduce any tendency of the cup to extrude under pressure a phonograph finish may be machined on the surface of the follower plate.
NOTE: The 8000 piston cups are center punched.
SEAL INFORMATION MATERIAL 90A URETHANE TEMPERATURE RANGE -65° to +220° F PRESSURE RANGE 0 to 1,200 PSI SPEED 3 FT/SEC PART NUMBER (Piston Cup Type)(Bore) - (Hole Size) -
SEAL INFORMATION TENSILE STRENGTH 35,000 PSI YIELD STRENGTH 18,000 PSI PART NUMBER (Prefix) - (ID) (CS) - (Width) -
SEAL INFORMATION TEMPERATURE RANGE -40° to +250° F TENSILE STRENGTH 10,600 PSI COMPRESSIVE STRENGTH 34,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (OD) (CS) - (Width) -
Style 614 rod bearings are available in nylon material. These products are used extensively in hydraulic cylinders due to their low rate of wear and non-scoring properties. Excellent for those heavy duty applications that require a sturdy bearing. Most of these bearings are solid, although some may be split.
SEAL INFORMATION TEMPERATURE RANGE -40° to +275° F TENSILE STRENGTH 25,000 PSI COMPRESSIVE STRENGTH 26,000 PSI PART NUMBER (Prefix) - (ID) - (Width) -
Manufactured using woven fabric-reinforced polyester resin, this material produces a dimensionally accurate rectangular strip which can be cut to any length. Low coefficient of friction and high compressive strength makes it an ideal bearing material. A common radial thickness of 1/8 in. allows the stacking of various widths. Size reference is marked every 6 in. on the strip. Available by the foot or rolls of 16 feet. Cutting is made easy by using Anvil type pruning shears. Wall tolerance ± .002 in., radial wall thickness = 0.124 to 0.121 in. Standard part numbers are gray in color.
TQ = Turquoise in color.SEAL INFORMATION TEMPERATURE RANGE -40° to +250° F TENSILE STRENGTH 8,000 PSI COMPRESSIVE STRENGTH 24,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (Width) -
Our 612F style flexible guide bearings, with a 1/8" radial thickness, offered in a boxed quantity. The strip can be cut to any length using anvil type pruning shears. Product length is 32' per box.
SEAL INFORMATION MATERIAL FABRICATED REINFORCED POLYESTER TEMPERATURE RANGE -40° to +250° F TENSILE STRENGTH 8,000 PSI COMPRESSIVE STRENGTH 24,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (W) x (TH) -
Flexible Guide Bearings are strips of filled PTFE. The material can be cut to any length to fit any rod or bore size without losing its concentricity. The filler material is shown below. NOTE: Glass filled material has a thickness tolerance of ±_.010 in. Bronze filled tolerance is ± .0025 in.
SEAL INFORMATION MATERIAL GLASS FILLED 60% BRONZE FILLED PTFE TEMPERATURE RANGE -50° to +400° F TENSILE STRENGTH 2,100 PSI COMPRESSIVE STRENGTH 1,500 PSI SPEED 12 FT/SEC PART NUMBER (Prefix) - (Width) B = Bronze Filled PTFE -
NOTE: The 6000 piston cups are center punched if there is no hole size indicated.
SEAL INFORMATION MATERIAL BUNA-N RUBBER TEMPERATURE RANGE -40° to +220° F PRESSURE RANGE 0 to 150 PSI SPEED 3 FT/SEC PART NUMBER (Piston Cup Type)(Bore) - (Hole Size) -
Note: "SC" suffix designates a Scarf Cut wear ring.
SEAL INFORMATION TEMPERATURE RANGE -40° to +275° F TENSILE STRENGTH 27,000 PSI COMPRESSIVE STRENGTH 26,000 PSI PART NUMBER (PREFIX) - (OD) - (HT) CROSS-SECTIONS 606 Prefix 1/16" C/S 608 Prefix 5/64" C/S 609 Prefix 3/32" C/S 610 Prefix .1" C/S 612 Prefix 1/8" C/S 616 Prefix 3/16" C/S 625 Prefix 1/4" C/S -
Used primarily as an anti-extusion device for u-seals, these back-up rings combine high performance with very low friction. 'ST' suffix designates a split ring.
SEAL INFORMATION MATERIAL PTFE TEMPERATURE RANGE -100° TO +500°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (prefix) - (Dash No.) (config.) -
SEAL INFORMATION MATERIAL BUNA-N RUBBER TEMPERATURE RANGE -40° TO +240° F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE SPEED 3 FT/SEC PART NUMBER (Prefix) - (Dash No.) -
Split NylonSEAL INFORMATION MATERIAL NYLON TEMPERATURE RANGE -40 ° TO +250°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.) -
Molded of 95A Durometer Urethane these back-up rings provide excellent extrusion resistance. Stretched for installation, they return quickly to their original size for easy installation.
NOTE: Sizes (Dash No.) corresponds to standard o-ring numbers.SEAL INFORMATION MATERIAL 95A DUROMETER URETHANE TEMPERATURE RANGE -65 ° TO +220°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.) -
Letter suffix:
T = Solid, ST = Split, TS = Spiral Cut, TW = .085 WideSEAL INFORMATION MATERIAL PTFE TEMPERATURE RANGE -325 ° TO +500°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.)(Config)
CROSS SECTIONS 000 Series 1/16" C/S 100 Series 3/32" C/S 200 Series 1/8" C/S 300 Series 3/16" C/S 400 Series 1/4" C/S -
Molded of 90A Durometer Buna-N Rubber, these 'Parback®' Style Dished Cross Section back-up rings provide excellent extrusion resistance. Stretched for installation, they return quickly to their original size for easy installation.
NOTE: Sizes (Dash No.) corresponds to standard O-ring numbers.SEAL INFORMATION MATERIAL 90A BUNA-N RUBBER TEMPERATURE RANGE -40° TO +240°F PRESSURE RANGE VARIES ACCORDING TO DIAMETRAL CLEARANCE PART NUMBER (Prefix) - (Dash No.)