The individual vee rings and adaptors listed here are the same high quality product found in our assembled vee packing sets. Stocking individual vee rings allows you to assemble sets to your specific requirements.

RING TYPES
T = TOP ADAPTOR - NYLON
B = BOTTOM ADAPTOR - NYLON/ NEO-FAB
F = NEO-FAB VEE RING
U = URETHANE VEE RING
R = RUBBER VEE RING.
(FOR MORE RUBBER VEE RINGS SEE OUR STYLE 835 RINGS)

If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.

A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.

If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.

A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.

To obtain best results from any style of piston cup, it is recommended that the piston properly support the heel of the cup. Recommended diametral clearance between the piston and cylinder wall are as follows:
1" to 2-1/4" .005"
2-1/2" to 4-3/4" .008"
5" to 10" .010"

The height of the machined shoulder most frequently used to control squeeze on the heel of the cup is as follows:
Cups 1/8" thick .116/.119"
Cups 5/32" thick .146/.149"
Cups 3/16" thick .178/.181"
The follower plate should be approximately .110" smaller than the ID of the cup. To reduce any tendency of the cup to extrude under pressure a phonograph finish may be machined on the surface of the follower plate.

NOTE: The 8000 piston cups are center punched.

Piston cups are constructed of rubberized fabric. Cups with no hole are center punched.
NOTE: If Product number ends in 'ED' the piston cups are specially sized for use in EDBRO Cylinders.

A heavy duty double-acting assembly, the capped piston T-seal exhibits excellent sealability, extrusion resistance and wearability. T-seals with 'BR' suffix utilize a Bronze Filled PTFE cap instead of the standard Glass Filled PTFE cap.

INSTALLATION OF PTFE PISTON SEALS
Installing PTFE piston seals is not always an easy task. The use of installation tools (Designated by a 'CTC-' product code prefix) is recommended but often not convenient when working with a wide variety of sizes and applications. Finger installations are practical with rings of smaller cross-sections. Using fingers or a rounded plastic stick, knead the ring over the piston into the groove. With rings of larger cross-sections it may be necessary to heat the ring. Warming the ring in water or oil at 130° F or 140° F for about 5 minutes will soften the material for easier installation. Always avoid inconsistent stretching or overstretching of the PTFE seal.

To prevent the PTFE ring from snapping into the wrong groove, cover wear ring grooves with plastic tape.

After seal installation, assembly of the cylinder may be difficult if the piston seal is loose on the piston or the cylinder has an inadequate leading edge chamfer. In such cases, compress the piston seal with belting or a suitable hose clamp. If the piston seal must pass threads or any other sharp edges during the cylinder assembly, cover the edges with plastic tape or wrap.

T-Seals are non-spiraling and extrusion resistant to 5,000 psi with improved tolerances.
IB = Intermediate Base, WB = Wide Base

Intermediate and Wide Base T-Seals are designed to fit MIL-5514F o-ring glands only and interchange with 1 o-ring / 1 back-up ring and 1 o-ring / 2 back-up ring grooves, respectively.