Molded in urethane, this wiper features a lip on the outer diameter to aid in contaminant exclusion.
| SEAL INFORMATION | |
|---|---|
| MATERIAL | URETHANE |
| TEMPERATURE RANGE | -30° to +200° F |
| SPEED | 3 FT/SEC |
| PART NUMBER | (Prefix) - (ID) x (OD) X (H) |
-
-
These parts are used as companion pieces for Cascade Vee Sets, used primarily as bearings. The bore sizes shown are nominal and are used in oversized bores of = .015 in. to = .030 in.
SEAL INFORMATION MATERIAL 60D POLYESTER TEMPERATURE RANGE -65° to +220° F SPEED FT/SEC PART NUMBER (Prefix) - (Bore Diameter) -
Molded in polyurethane this buffer is a simple flat, washer-like profile
SEAL INFORMATION MATERIAL URETHANE TEMPERATURE RANGE -40° to +200° F PRESSURE RANGE 0 to 5,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (ID) x (OD) x (H) -
Snap-In WiperSEAL INFORMATION MATERIAL NYLON TEMPERATURE RANGE -40° to +212° F SPEED 3 FT/SEC PART NUMBER (Prefix) - (Size) -
UKR u-seals are designed to act as a positive sealing, low friction replacement for conventional rubber u-seals. Molded from polyurethane, UKR u-seals provide long life and high resistance against extrusion. Low friction allows these seals to run smoothly in lubricated or non-lucricated cylinder. Available for rod sealing, the flexible dynamic lip provides very low breakaway friction and steady motion. -
These rings are split for ease of installation and are retained in a groove. Their use is primarily to retain a single acting piston seal. Commonly they are used with MUFN style piston seals.
SEAL INFORMATION MATERIAL ACETAL TEMPERATURE RANGE -22° to +212° F PART NUMBER (Prefix) - (ID) x (OD) -
UKP u-seals are designed to act as a positive sealing, low friction replacement for conventional rubber u-seals. Molded from polyurethane, UKP u-seals provide long life and high resistance against extrusion. Low friction allows these seals to run smoothly in lubricated or non-lubricated cylinder. Available for bore sealing, the flexible dynamic lip provides very low breakaway friction and steady motion. -
Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.FLUOROCARBON = "V"
BFM = 58D DUROMETER FLUOROTREL -65° TO +275° F BHN = 85A DUROMETER HYDROGENATED NITRILE -50° to +320° F BPM = 58D DUROMETER POLYMYTE -65° to +275° F / -65° to +180° F IN WATER BASED FLUIDSSEAL INFORMATION MATERIAL 90A FLUOROCARBON | 95A URETHANE TEMPERATURE RANGE -20° to +400° F | -40° to +200° F PRESSURE RANGE 0 to 2,000 PSI | 0 to 5,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix)(CS) - (Inside Dia) - (Height) 
Standard - Height and cross section are equal, thus giving a square seal. Utilizes type 'D' lip Typical Part Number P25-02.500 
Deep - Utilizes the same 'D' lip, but the seal height is greater than the cross section, thus giving a retangular shape. Typical Part Number P25-02.500-37D 
Type B - Same dimensions as the Deep seal. Beveled lip design provides better film breaking. Utilizes type 'B' lip. Typical Part Number U25-02.500-37B -
Incorporating a rubber seal lip and a rubberized fabric heel, this seal provides excellent sealability and high strength.
SEAL INFORMATION MATERIAL NITRILE / FABRIC BASE TEMPERATURE RANGE -22° to +212° F PRESSURE RANGE 0 to 2,900 PSI SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (ID) x (OD) x (H) -
Intermediate and Wide Base T-Seals are designed to fit MIL-5514F o-ring glands only and interchange with 1 o-ring / 1 back-up ring and 1 o-ring / 2 back-up ring grooves, respectively.
SEAL INFORMATION MATERIAL BUNA-N RUBBER SEAL - HARD PLASTIC BACK-UPS TEMPERATURE RANGE -35° to +220° F PRESSURE RANGE 0 to 5,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (Size) -
This wiper is a heavy duty scraper molded from a hard nylon material.
SEAL INFORMATION MATERIAL NYLON TEMPERATURE RANGE -40° to +212° F SPEED 3 FT/SEC PART NUMBER (Prefix) - (ID) x (OD) X (H) -
Caterpillar - 1 Piece Rod Buffer SealSEAL INFORMATION MATERIAL 92A URETHANE TEMPERATURE RANGE -40° TO +200° F PRESSURE RANGE 0 to 5,000 PSI SPEED 3 FT/SEC 12FT/SEC -
Designed specifically for rod application, the short lip design and solid 'U' cavity provide high sealability at low pressure. At the heel, a secondary lip provides stability, friction-reducing lube retention, and a contaminant blocker. Molded in polyurethane for excellent wear resistance.
SEAL INFORMATION MATERIAL URETHANE TEMPERATURE RANGE -22° to +220° F PRESSURE RANGE 0 to 5,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (ID) x (OD) x (H) -
Molded from tough polyurethane material, these seals offer high resistance to wear and abrasion. Energized with a four-lobed ring they have greatly increased low pressure performance.
SEAL INFORMATION MATERIAL URETHANE TEMPERATURE RANGE -40° to +200° F PRESSURE RANGE 0 to 5,000 PSI SPEED 3 FT/SEC SUFFIX HT = HIGH TEMPERATURE PART NUMBER (Prefix) - (ID) x (OD) x (H) -
NOTE: The 6000 piston cups are center punched if there is no hole size indicated.
SEAL INFORMATION MATERIAL BUNA-N RUBBER TEMPERATURE RANGE -40° to +220° F PRESSURE RANGE 0 to 150 PSI SPEED 3 FT/SEC PART NUMBER (Piston Cup Type)(Bore) - (Hole Size)
