Molded in nitrile, this wiper is for light duty applications.
| SEAL INFORMATION | |
|---|---|
| MATERIAL | NITRILE |
| TEMPERATURE RANGE | -22° to +212° F |
| SPEED | 3 FT/SEC |
| PART NUMBER | (Prefix) - (ID) x (OD) X (H) |
-
-
If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.
SEAL INFORMATION MATERIAL FABRIC REINFORCED RUBBER
AND BUNA-NTEMPERATURE RANGE -40° TO +250° F PRESSURE RANGE SEE CHART BELOW SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (ID) - (OD) A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.
PRESSURE RATING OF MULTIPLE RINGS PRESSURE P.S.I. NUMBER OF RINGS 250 - 500 3 500 - 2,000 4 2,000 - 5,000 5 5,000 - 8,000 6 -
If your design is of medium to high pressure it is recommended that you utilize fabric reinforced rings. The following is a guide to pressure rating of multiple rings, including flat bottom rings.
SEAL INFORMATION MATERIAL FABRIC REINFORCED RUBBER
AND BUNA-NTEMPERATURE RANGE -40° TO +250° F PRESSURE RANGE SEE CHART BELOW SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (ID) - (OD) A homogeneous ring may be also used for sealing at low pressure. Do not include the homogeneous ring in calculating pressure rating. Due to the different material, it is difficult to rate this type of ring. If you wish to use all homogeneous rings, tests should be conducted to verify design stability.
PRESSURE RATING OF MULTIPLE RINGS PRESSURE P.S.I. NUMBER OF RINGS 250 - 500 3 500 - 2,000 4 2,000 - 5,000 5 5,000 - 8,000 6 -
Style 614 rod bearings are available in nylon material. These products are used extensively in hydraulic cylinders due to their low rate of wear and non-scoring properties. Excellent for those heavy duty applications that require a sturdy bearing. Most of these bearings are solid, although some may be split.
SEAL INFORMATION TEMPERATURE RANGE -40° to +275° F TENSILE STRENGTH 25,000 PSI COMPRESSIVE STRENGTH 26,000 PSI PART NUMBER (Prefix) - (ID) - (Width) -
Style PU seals are molded from high quality urethane and designed specifically for piston applications. -
T-Seals are non-spiraling and extrusion resistant to 5,000 psi with improved tolerances.
IB = Intermediate Base, WB = Wide Base
Intermediate and Wide Base T-Seals are designed to fit MIL-5514F o-ring glands only and interchange with 1 o-ring / 1 back-up ring and 1 o-ring / 2 back-up ring grooves, respectively.SEAL INFORMATION MATERIAL BUNA-N RUBBER SEAL - HARD PLASTIC BACK-UPS TEMPERATURE RANGE -35° to +220° F PRESSURE RANGE 0 to 5,000 PSI SPEED 3 FT/SEC PART NUMBER (Prefix) - (Size) -
Piston cups are constructed of rubberized fabric. Cups with no hole are center punched.
NOTE: If Product number ends in 'ED' the piston cups are specially sized for use in EDBRO Cylinders.SEAL INFORMATION MATERIAL COTTON FABRIC & RUBBER TEMPERATURE RANGE -35° to +220° F PRESSURE RANGE 0 to 2,500 PSI SPEED 1.5 FT/SEC PART NUMBER (Piston Cup Type)(Bore) - (Hole Size) -
This wiper features a lip on top of the shoulder which makes contact with the throat of the groove. This serves to prevent contaminants from entering the groove.
SEAL INFORMATION MATERIAL URETHANE TEMPERATURE RANGE -30° to +220° F PART NUMBER (Prefix) - (ID) x (OD) X (H) -
Incorporating a rubber seal lip, a rubberized fabric heel and an acetal back-up ring. This seal provides excellent sealability and high extrusion resistance.
SEAL INFORMATION MATERIAL NBR 80 DURO SEAL
NEO-FAB HEEL
ACETAL ANTI-EXTRUSION RINGTEMPERATURE RANGE -22° to +212° F PRESSURE RANGE 0 to 6,000 PSI PART NUMBER (Prefix) - (ID) x (OD) x (H) -
Used interchangeably for piston or rod sealing, these u-seals employ the same tough urethane material found in our Heavy Duty Rod and Piston U-Seals. -
The PS1800 provides low friction, high strength piston sealing. The PS1800 also provides double-acting piston sealing in a compact design that meets the requirements of ANSI/B93-32-1973. NOTE: Piston diameter 'I' dimensions are given for pistons without wear rings.
SEAL INFORMATION MATERIAL 15% GLASS FILLED PTFE SEAL RUBBER ENERGIZER TEMPERATURE RANGE -40° to +220° F PRESSURE RANGE 0 to 5,000 PSI SPEED 12 FT/SEC PART NUMBER (Piston Seal)(Type of Seal) - (Size) -
NOTE: Piston diameter 'I' dimensions are given for pistons without wear rings.
SEAL INFORMATION MATERIAL 15% GLASS FILLED PTFE SEAL RUBBER ENERGIZER TEMPERATURE RANGE -40° to +220° F PRESSURE RANGE 0 to 5,000 PSI SPEED 12 FT/SEC PART NUMBER (Piston Seal)(Type of Seal) - (Size) -
Utilizing a double lip of nitrile bonded to a carbon steel case, this wiper prevents contaminant ingression at the wiping lip and around the outer case.
SEAL INFORMATION MATERIAL URETHANE TEMPERATURE RANGE -30° to +200° F SPEED 3 FT/SEC -
A double acting piston seal with many features; two compact seal edges to concentrate the load against the dynamic surface, a cavity between the two external seal edges to retain fluid (reducing friction and wear), side grooves to allow pressure to load the energizer in all working conditions, high sealing performance at low pressure, excellent wear-resistance, and high resistance against extrusion.
SEAL INFORMATION MATERIAL 97A URETHANE SEAL
70A NITRILE EXPANDERTEMPERATURE RANGE -22° TO +210° F PRESSURE RANGE 0 TO 5,800 PSI SPEED 1.5 FT/SEC PART NUMBER (Prefix) - (OD) x (ID) x (W) MAXIMUM EXTRUSION GAP Pressure (PSI) 725 1450 2900 4350 5800 Max Diametrical Gap (inches) 0.047 0.031 0.016 0.010 0.007 -
MCU Heavy Duty Metal Clad
Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.SEAL INFORMATION MATERIAL 92A URETHANE TEMPERATURE RANGE -65° to +230° F PART NUMBER (Prefix) - (Size) -
Incorporating a rubber seal lip, a rubberized fabric heel and an acetal back-up ring. This seal provides excellent sealability and high extrusion resistance.